Category:TS-409

From Qnap-Wiki

Hardware

PCB Front

PCB Back

CN9 is the serial console. GND, RX, VCC and TX are clearly marked. The signals are 3.3V levels, 115200 baud, 8 bits, no parity, 1 stop bit.

Reviews

http://www.smallnetbuilder.com/content/view/30324/75/

Useful Links

How to install Ipkg

How to install Subversion (using Ipkg)

How to get Debian on QNAP

U-boot

        __  __                      _ _
       |  \/  | __ _ _ ____   _____| | |
       | |\/| |/ _` | '__\ \ / / _ \ | |
       | |  | | (_| | |   \ V /  __/ | |
       |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: DB-88F5X81-DDR2-A/B LE, boardId=7
 QNAP SYSTEMS, INC.
QNAP:MV_INCLUDE_GIG_ETH


U-Boot 1.1.4 (Jul 26 2007 - 11:26:33) Marvell version: 2.3.23

U-Boot code: 00200000 -> 0027FFF0  BSS: -> 00292E10

Soc: 88F5281 D0 (DDR2)
CPU running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz

DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  32bit width
[8192kB@ff800000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB
Flash:  8 MB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done

CPU : ARM926 (Rev 0)
Streaming disabled
VFP initialized to Run Fast Mode.

USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
CPU: Write allocate enabled
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=172.17.21.243
rootpath=/mnt/armfs/
cpuName=926
bootargs=console=ttyS0,115200
CASset=min
MALLOC_len=4
ethprime=egiga0
netbsd_gw=192.168.0.254
netbsd_mask=255.255.255.0
netbsd_fs=nfs
netbsd_server=192.168.0.1
netbsd_rootdev=mgi0
netbsd_add=0x800000
netbsd_get=tftpboot $(netbsd_add) $(image_name)
netbsd_set_args=setenv bootargs nfsroot=$(netbsd_server):$(rootpath) fs=$(netbsd_fs) ip=$(ipaddr) serverip=$(netbsd_server) mask=$(netbsd_mask) gw=$(netbsd_gw)
rootdev=$(netbsd_rootdev) ethaddr=$(ethaddr)
netbsd_boot=bootm $(netbsd_add) $(bootargs)
netbsd_bootcmd=run netbsd_get ; run netbsd_set_args ; run netbsd_boot
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:egiga0:none
image_name=uImage
standalone=fsload 0x400000 $(image_name);setenv bootargs $(bootargs) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x400000;
ethaddr=00:00:00:00:51:81
eth1addr=00:00:00:00:51:82
pciMode=host
ethact=egiga0
fsargs=setenv bootargs console=ttyS0,115200n8 root=/dev/ram rw initrd=0x800000,0x3fffff
prefs=cp.b 0xffa00000 0x800000 0x3fffff
usbMode=host
usb0Mode=host
unprot=protect off 0xfff60000 0xffffffff
prekernel=cp.b 0xff800000 0x400000 0x1fffff
bootcmd=run prekernel;run prefs;run fsargs;run unprot;bootm 0x400000
serverip=172.17.21.8
stdin=serial
stdout=serial
stderr=serial
enaDebugLed=yes
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
enaVFP=yes
enaWrAllo=yes
enaICPref=yes
enaDCPref=yes
bootdelay=3
disaMvPnp=no
overEthAddr=no

Environment size: 1491/4092 bytes
Marvell>>

Kernel output

.....
Un-Protected 5 sectors
## Booting image at 00400000 ...
   Image Name:   Linux-2.6.21.1-qnap
   Created:      2008-03-24  10:44:47 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1994620 Bytes =  1.9 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux.................................................................................................................................. done, booting the kernel.
Linux version 2.6.21.1-qnap (root@NASARM2) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #7 Mon Mar 24 18:44:37 CST 2008
CPU: ARM926EJ-S [41069260] revision 0 (ARMv5TEJ), cr=00053177
Machine: Feroceon
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists.  Total pages: 65024
Kernel command line: console=ttyS0,115200n8 root=/dev/ram rw initrd=0x800000,0x3fffff
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB 0MB 0MB 0MB = 256MB total
Memory: 251520KB available (3764K code, 280K data, 128K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Sys Clk = 166666667, Tclk = 166666667
Orion2 D0 or less. Enable VFP.

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size  64MB
PEX0_IO ....base f2000000, size   1MB
PCI0_MEM ....base ec000000, size  64MB
PCI0_IO ....base f2100000, size   1MB
INTER_REGS ....base f1000000, size   1MB
DEVICE_CS0 ....base fa000000, size   2MB
DEVICE_CS1 ....base fc000000, size  32MB
DEVICE_CS2 ....base fa800000, size   1MB
DEV_BOOCS ....base ff800000, size   8MB

  Marvell Development Board (LSP Version 2.2.2_NAS_GDP) - Large Filesystem Support-- DB-88F5X81-DDR2-A  Soc: 88F5281 D0

 Detected Tclk 166666667 and SysClk 166666667
Marvell USB EHCI Host controller #0: a067c800
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4095K
QNAP RTC initializing....
Initializing RTC is completed.
RTC registered
 Detected Tclk 166666667, BASE_BAUD 10416666, Baud divisor 542
qnap_pic_init: succeed to register misc device
tsinfo: create proc systemp successfully
tsinfo: create proc systemp successfully
qkv_init: succeed to register misc device
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
<QNAP>current->mm is null.
Done.
audit: initializing netlink socket (disabled)
audit(1.097:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
io scheduler noop registered (default)
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Ethernet Driver 'mv_ethernet':
  o Uncached descriptors in DRAM
  o DRAM SW cache-coherency
  o TCP segmentation offload enabled
  o Checksum offload enabled
  o Driver statistics enabled
  o Marvell ethtool proc enabled
  o Rx desc: 128
  o Tx desc: 256
  o Loading network interface 'eth0'
 Wait 30 seconds to initialize mvAdapter.
 Wait 0 seconds to initialize scsi 0.
scsi0 : Marvell SCSI to SATA adapter
 Wait 0 seconds to initialize scsi 1.
scsi1 : Marvell SCSI to SATA adapter
 Wait 5 seconds to initialize scsi 2.
scsi2 : Marvell SCSI to SATA adapter
 Wait 5 seconds to initialize scsi 3.
scsi3 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access     SAMSUNG  SP2504C          VT10 PQ: 0 ANSI: 3
scsi 1:0:0:0: Direct-Access     SAMSUNG  SP2504C          VT10 PQ: 0 ANSI: 3
scsi 2:0:0:0: Direct-Access     SAMSUNG  SP2504C          VT10 PQ: 0 ANSI: 3
scsi 3:0:0:0: Direct-Access     SAMSUNG  SP2504C          VT10 PQ: 0 ANSI: 3
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: write cache: enabled, read cache: enabled, supports DPO and FUA
 sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdb: write cache: enabled, read cache: enabled, supports DPO and FUA
 sdb: sdb1 sdb2 sdb3 sdb4
sd 1:0:0:0: Attached scsi disk sdb
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdc: write cache: enabled, read cache: enabled, supports DPO and FUA
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdc: write cache: enabled, read cache: enabled, supports DPO and FUA
 sdc: sdc1 sdc2 sdc3 sdc4
sd 2:0:0:0: Attached scsi disk sdc
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdd: write cache: enabled, read cache: enabled, supports DPO and FUA
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sdd: write cache: enabled, read cache: enabled, supports DPO and FUA
 sdd: sdd1 sdd2 sdd3 sdd4
sd 3:0:0:0: Attached scsi disk sdd
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 3:0:0:0: Attached scsi generic sg3 type 0
physmap platform flash device: 00800000 at ff800000
cmdlinepart partition parsing not available
RedBoot partition parsing not available
QNAP Set mtd partition
Using physmap partition information
cfi_flash: Found 1 x16 devices at 0x0 in 8-bit bank
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
cmdlinepart partition parsing not available
Creating 6 MTD partitions on "cfi_flash":
0x00780000-0x00800000 : "U-Boot"
QNAP(ori): slave->mtd.flags = 800, <5>QNAP: slave->mtd.flags = 800
0x00000000-0x00200000 : "Kernel"
QNAP(ori): slave->mtd.flags = c00, <5>QNAP(MTD_WRITEABLE): slave->mtd.flags = c00
0x00200000-0x00600000 : "RootFS1"
QNAP(ori): slave->mtd.flags = c00, <5>QNAP(MTD_WRITEABLE): slave->mtd.flags = c00
0x00600000-0x00700000 : "RootFS2"
QNAP(ori): slave->mtd.flags = c00, <5>QNAP(MTD_WRITEABLE): slave->mtd.flags = c00
0x00760000-0x00780000 : "U-Boot Config"
QNAP(ori): slave->mtd.flags = c00, <5>QNAP(MTD_WRITEABLE): slave->mtd.flags = c00
0x00700000-0x00760000 : "NAS Config"
QNAP(ori): slave->mtd.flags = c00, <5>QNAP(MTD_WRITEABLE): slave->mtd.flags = c00
$Id: pmc551.h,v 1.1.1.1 2007/09/07 08:41:55 ricky Exp $
Ramix PMC551 PCI Mezzanine Ram Driver. (C) 1999,2000 Nortel Networks.
pmc551: not detected
block2mtd: version $Revision: 1.1.1.1 $
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
feroceon-ehci feroceon-ehci.4523: EHCI Host Controller
feroceon-ehci feroceon-ehci.4523: new USB bus registered, assigned bus number 1
feroceon-ehci feroceon-ehci.4523: irq 17, io mem 0x00000000
feroceon-ehci feroceon-ehci.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
usb 1-1: new high speed USB device using feroceon-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
drivers/usb/net/rtl8150.c: rtl8150 based usb-ethernet driver v0.6.2 (2004/08/27)
usbcore: registered new interface driver rtl8150
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver dm9601
usbcore: registered new interface driver gl620a
usbcore: registered new interface driver net1080
usbcore: registered new interface driver plusb
usbcore: registered new interface driver rndis_host
usbcore: registered new interface driver cdc_subset
usbcore: registered new interface driver MOSCHIP usb-ethernet driver
usbcore: registered new interface driver mdc800
drivers/usb/image/mdc800.c: v0.7.5 (30/10/2000):USB Driver for Mustek MDC800 Digital Camera
usbcore: registered new interface driver microtekX6
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1     23 MB/s
raid6: int32x2     39 MB/s
raid6: int32x4     48 MB/s
raid6: int32x8     45 MB/s
raid6: using algorithm int32x4 (48 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
   arm4regs  :   429.600 MB/sec
   8regs     :   330.000 MB/sec
   32regs    :   513.600 MB/sec
raid5: using function: 32regs (513.600 MB/sec)
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 5
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 128K

System start

Start config_util...
Flash NASConfig done.
Start to mirror ROOT part...
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
config_util: ret=0, /dev/sda1 is successfully mounted.
config_util: config file=/mnt/HDA_ROOT/.conf
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
config_util: ret=0, /dev/sdb1 is successfully mounted.
config_util: config file=/mnt/HDB_ROOT/.conf
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdc1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
config_util: ret=0, /dev/sdc1 is successfully mounted.
config_util: config file=/mnt/HDC_ROOT/.conf
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdd1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
config_util: ret=0, /dev/sdd1 is successfully mounted.
config_util: config file=/mnt/HDD_ROOT/.conf
md: md9 stopped.
md: bind<sdb1>
md: bind<sdc1>
md: bind<sdd1>
md: bind<sda1>
raid1: raid set md9 active with 4 out of 4 mirrors
mdadm: /dev/md9 has been started with 4 drives.
Mirror of ROOT succeeded.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Start to mirror RFS_EXT part...
md: md13 stopped.
md: bind<sdb4>
md: bind<sdc4>
md: bind<sdd4>
md: bind<sda4>
raid1: raid set md13 active with 4 out of 4 mirrors
mdadm: /dev/sda4 has been started with 4 drives.
config_util: (0) /dev/sda4 size = 71808
Mirror of RFS_EXT succeeded.
config_util finished.
mount HDD root device
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
mount /dev/md9 successful.
HD_Model_Name=TS-409
Model_Name=TS-409
Update Extended rcX_init.d...
4+0 records in
4+0 records out
Extract RootFS2...
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md9, internal journal
EXT3-fs: mounted filesystem with ordered data mode. 
mountall: mount /dev/md9 successful.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md13, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/ram0                 9911      6920      2991  70% /
tmpfs                    16384         8     16376   0% /tmp
/dev/sda4                63461     44517     18944  70% /mnt/ext
Enable watchdog...
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
sysinfo: Module loaded.
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
NTFS driver 2.1.28 [Flags: R/W MODULE].
initializing MAC address...
eth0: mac address changed
MAC_ADDR 00:08:9B:AC:81:80
storage_boot_init 1 ...
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
mdadm: /dev/sda2 appears to be part of a raid array:
    level=raid1 devices=2 ctime=Wed Apr  2 23:15:42 2008
md: bind<sda2>
md: md4: raid array is not clean -- starting background reconstruction
raid1: raid set md4 active with 1 out of 1 mirrors
mdadm: array /dev/md4 started.
Start_Swapping(): add swap raid device into RAID_CONF_FILE
Adding 530040k swap on /dev/md4.  Priority:-1 extents:1 across:530040k
md: bind<sdb2>
RAID1 conf printout:
 --- wd:1 rd:2
 disk 0, wo:0, o:1, dev:sda2
 disk 1, wo:1, o:1, dev:sdb2
md: recovery of RAID array md4
md: minimum _guaranteed_  speed: 1000 KB/sec/disk.
md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
md: using 128k window, over a total of 530048 blocks.
mdadm: added /dev/sdb2
md: bind<sdc2>
mdadm: added /dev/sdc2
md: bind<sdd2>
mdadm: added /dev/sdd2
md: md4: recovery done.
RAID1 conf printout:
 --- wd:2 rd:2
 disk 0, wo:0, o:1, dev:sda2
 disk 1, wo:0, o:1, dev:sdb2
config hidden config directory exist, create symbolic link /etc/config... [OK]
Check config files...start
Check config files...end
Writing model version information...
Writing model version info...[OK]
log hidden config directory exist, create symboloc link /etc/logs... [OK]
Starting Disk initialized:
storage_boot_init 2 ...
md: md0 stopped.
md: bind<sdc3>
md: bind<sdd3>
md: bind<sda3>
md: bind<sdb3>
raid5: device sdb3 operational as raid disk 0
raid5: device sda3 operational as raid disk 3
raid5: device sdd3 operational as raid disk 2
raid5: device sdc3 operational as raid disk 1
raid5: allocated 4212kB for md0
raid5: raid level 5 set md0 active with 4 out of 4 devices, algorithm 2
RAID5 conf printout:
 --- rd:4 wd:4
 disk 0, o:1, dev:sdb3
 disk 1, o:1, dev:sdc3
 disk 2, o:1, dev:sdd3
 disk 3, o:1, dev:sda3
mdadm: /dev/md0 has been started with 4 drives.
storage_boot_init.c: Start raid device /dev/md0 successfully
md0 : active raid5 sdb3[0] sda3[3] sdd3[2] sdc3[1]
md0 : active raid5 sdb3[0] sda3[3] sdd3[2] sdc3[1]
md0 : active raid5 sdb3[0] sda3[3] sdd3[2] sdc3[1]
md0 : active raid5 sdb3[0] sda3[3] sdd3[2] sdc3[1]
storage_boot_init.c:     /dev/md0 is active.
e2fsck 1.40-WIP (02-Oct-2006)
/dev/md0: clean, 54403/91160576 files, 151825627/182291424 blocks
kjournald starting.  Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with writeback data mode.
storage_boot_init 6 ...
Create_Disk_External_Storage_Conf..............

Stopping network...Stopped.
Starting network...DHCP
eth0: link down
network.sh: write_hosts
169.254.100.100
eth0: link up, full duplex, speed 1 Gbps
Speed: 1000
ddns enable
ddns update.
Initializing random number generator... done.
Starting thttpd services: thttpd.
Starting Qthttpd services: Qthttpd.
Starting Winbind services:Starting SMB services: smbd nmbd.
Starting FTP services: proftpd.
Starting NFS services:  disabled.
Starting btd daemon...
Starting ImRd service:
msgget: Calling msgget(7843,950)
msgget: msgget succeeded: msgid = 131076
.
Starting periodic command scheduler: crond[1470]: crond 2.3.2 dillon, started, log level 9

crond. 
use PIC1 as default image
Starting ntpdate daemon:
Starting stunnel services:2008.04.04 01:01:44 LOG7[1498:16384]: RAND_status claims sufficient entropy for the PRNG
2008.04.04 01:01:44 LOG6[1498:16384]: PRNG seeded successfully
2008.04.04 01:01:44 LOG7[1498:16384]: Certificate: /etc/stunnel/stunnel.pem
2008.04.04 01:01:44 LOG7[1498:16384]: Key file: /etc/stunnel/stunnel.pem
2008.04.04 01:01:44 LOG7[1498:16384]: SSL context initialized for service https
 stunnel.
Starting genpowerd: disabled
Starting sshd services: sshd.
Starting telnet services: telnetd: starting
  port: 23; login program: /bin/naslogin
utelnetd.
Starting TwonkyMedia: disabled.
Starting iTune Services: disabled.

init_nas.sh: Restart bcclient.
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
get_hdd_model_size(TS_201) - SAMSUNG SP2504C         VT10 [232.89 GB].
sendmail: Cannot open smtp.free.fr:25
Starting rsync server...
.
/share/MD0_DATA/Public
/share/MD0_DATA/Qusb
/share/MD0_DATA/Qweb
/share/MD0_DATA/Qmultimedia
/share/MD0_DATA/Qdownload
init_nas.sh: check_last_degrade_error storage_boot_init 5
storage_boot_init 5 ...
check_last_degrade_error...
init_nas.sh: set LED with storage_boot_init 4
storage_boot_init 4 ...
storage_boot_init.c: Set Status LED...
[/etc/config/runone/*] do nothing
Thread join fail: No such file or directory
Starting ddns update: rule type=0, num=0
Init Semaphore for NAS Success
The system had been started 56 time(s).
Starting AppleTalk services: Qmultimedia: attribute not found.
ez-ipupdate.

_OK!
network.sh: write_hosts
169.254.100.100


Welcome to QNAP Systems Inc,. Marvell(169.254.100.100) development environment.

TS409 login: